Request Service

 

 

They are making a number of great pointers relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround overall in the content below.

Mounting a bath tub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably difficult project. If the old tub is easily obtainable, the project can move speedily; if you have to open a wall to eliminate the old tub as well as place the brand-new bathtub, the task is much harder. In either case, the job is within a home handyman's skills, although you will need a helper to leave the old tub and set in the new one. Make certain you have actually certified on your own for the job and are comfortable attempting it. Instead of hiring a professional to take over a halfway-completed job, it is much better to take into consideration utilizing one prior to you start. Chances are you may need a professional plumber to make tube connections.
This post will certainly assist you set up a brand-new tub in your restroom if you have already gotten a new tub and don't need to transform the setup of your previous water pipelines.
Your devices and material checklist ought to comprise the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Planning for the Setup

First of all, the supporting frame provided with the bath should be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to make sure that if the faucet features a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to currently be ready to be suited its final placement.

 

 

Removing Old Taps

If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain any kind of water remaining in the system. The procedure of removing the existing taps can be fairly problematic because of the restricted accessibility that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the continuing to be water that will originate from the pipelines. Once the supply pipelines have actually been removed, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing substance.
Prior to carrying on to fit the brand-new faucets, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.

 

 

Installing the Tub

Making use of both wood boards under its feet, position the bath tub in the required setting. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four small factors.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the bathtub until the spirit level checks out level.
To install taps, fit the bottom of the furthest flexible tap connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the supply of water and also check all joints and new pipework for leaks as well as tighten them if required. Fill up the tub and also check the overflow electrical outlet and the normal outlet for leaks.
Finally, fix the bath paneling as defined in the supplier's user's manual. Tiling and also securing around the tub ought to wait up until the tub has been used at least once as this will resolve it into its final position.

 

 

Suitable New Touches

If the tails of the new taps are plastic, then you will need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washers are in location between the faucet and also the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The former type needs to be linked to the tap ends first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Bath tub

In the location where the bath meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall between the bathroom as well as the tiling, leading to problems with dampness as well as possible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your components and installations. They are sold in tubes and also cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to permit the movement experienced when the bathtub is in use. The sealer can crack relatively very early if you do not consider this activity prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles making use of waterproof or waterproof sticky and also cement.

 

Bathtub Installation

 

How Important Is A Bathtub To Your Home?

 

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

 

Install Piping Before Tub

 

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

 

Position the Tub

 

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

 

Assemble Drain Connections

 

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

 

Place a Pipe For the Shower Head

 

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

 

Attaching Hot and Cold Water Lines

 

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

 

Install the Spout

 

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

 

Check For Leaks

 

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

 

estore the Bathroom Wall

 

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

 

I have been very serious about A Step-by-Step Guide to Installing a Bathtub and I'm hoping you liked my blog post. Do you know about somebody else who is involved in the topic? Feel free to promote it. Thank you so much for going through it.

Book Appointment